Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20

Thread: BPS Tech Work Thread

  1. #11
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    From parts to fully functional, this RF project was done for "THE Hulk" here on CC. The latest and greatest parts inside and out on this sleeper body had it shooting great! Thanks to Hulk for the opportunity to put it together for him

    Last edited by Euangelion; 12-19-2017 at 07:46 PM.

  2. #12
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    Slacking on work updates. Finished an ego8 refresh. Low velocity led to replacement of torn qev diaphragm along with fresh orings and grease. Shooting a smooth 285 and ready to hit the field again


  3. #13
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    Another alias across the bench. Quick oring swap and pressure resets got this beast back on the field


  4. #14
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762

  5. #15
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    Another ground up build for CC's own hammontw. Meteor M1 with all of the of the latest and greatest bits. Assembled, timed, tuned, and tested. This one needed some beefier Madmann springs and a slightly higher HPR pressure to seal the red chamber valve. Over time the cup seal should wear in and can swap in some others for an even more refined feel.


    how do i delete a facebook account

  6. #16
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    A straightforward parts installation and tuning on this mini gs. Swapped the stock frame for a nummech vlx. Greatly improved ergonomics and pretty slick looking too! Chronod back to a steady 290 after some bolt cleaning and oring replacement as well


  7. #17
    Join Date
    Dec 2017
    Location
    Cincinnati, OH
    Posts
    86
    Fantastic job! John will take care of you!! Couldn't be happier!
    WTB: MECHANICAL ECLIPSE AUTOCOCKER!!! PM ME IF YOU'RE READY TO PART WITH YOURS!!

  8. #18
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    Thank you for the vote of confidence!

    Here are a couple more beauties that were wrapped up for mrmojoz here as well.

    The Orracle was a quick clean, pressure check, and tune. The other needed some TLC as a lot of the seals were decaying after a long time stored away. Ram and LPRs were cleaned and built back up, pressures reset, dialed in, and it's back to ripping away!




  9. #19
    Join Date
    Nov 2007
    Location
    New York
    Posts
    3,762
    Another couple for a fellow CC member

    Inception needed general dialing in and quick clean to get up and going. A new matching evo ram was sourced for the twister and gun was taken to completion with build up, timing, and chrono. Two gorgeous markers to work on and both are shooting like champs.




  10. #20
    Join Date
    Nov 2006
    Location
    Dublin, CA
    Posts
    1,601
    Quote Originally Posted by Euangelion View Post
    Another couple for a fellow CC member

    Inception needed general dialing in and quick clean to get up and going. A new matching evo ram was sourced for the twister and gun was taken to completion with build up, timing, and chrono. Two gorgeous markers to work on and both are shooting like champs.



    Both mine.... Both came back running smoothly! Great work, communication, and turnaround. Impeccable work by John.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •